AFUE – Stands for Annual Fuel Utilization Efficiency. This number represents how efficiently a furnace converts fuel to energy. The higher the rating, the more fuel-efficient the furnace is.Percentage of fuel used for heating.
Air Handler – The portion of your air conditioner or heating system that forces air through your home’s ductwork.
BTU – Stands for British Thermal Units. This number indicates the amount of heat it takes to raise one pound of water one degree Fahrenheit. The higher the BTU rating, the larger the heating capacity of the furnace or air conditioner. Homes are measured to determine the number of BTUs required from a heating or cooling system.
Capacity – Heating and cooling equipment capacities are measured in BTUs. How much heat can the air conditioning unit remove.
Carbon Monoxide – A colorless, odorless, highly poisonous gas produced when carbon burns without sufficient air nearby.
CFM – Stands for Cubic Feet per Minute. A measurement of airflow that indicates how many cubic feet of air pass by a stationary point in one minute. The higher the number, the more air is being forced through the system.
Compressor – The Compressor is the most important piece of a heating or cooling system. Located in the outdoor unit, the compressor is responsible for pumping refrigerant throughout the system.
Condenser Coil – The outdoor portion of a heating or cooling system that either releases or collects heat from the outside air, depending on the time of year. The Condenser Coil is connected directly to the home’s Air Handler and is also known as the Outdoor Coil.
Damper – A movable plate that controls airflow through a ductwork system. Dampers are used to direct air to the areas of the home that need it most.
Ductwork – Hollow pipes used to transfer air from the Air Handler to the air vents throughout your home. Ductwork is one of the most important components of a home heating and cooling system.
Evaporator Coil – This is where refrigerant evaporates as it removes heat from the air that is passed over it. The Evaporator Coil is located in the indoor unit and is also referred to as the Indoor Coil.
FAQ – Stands for Frequently Asked Question. Also refers to a list of Frequently Asked Questions. More information…
Heat Exchanger – The part of a furnace that transfers heat to nearby air. That air is then distributed through the Ductwork throughout your home.
Heat Pump – A heating and air conditioning unit that heats or cools by moving heat. More information…
HSPF – Stands for Heating Seasonal Performance Factor. Indicates how efficiently a Heat Pump is working. A higher number means the unit works more efficiently. Most new units have ratings from 7.0 to 9.4.
Humidifier – A component that adds moisture to the air before it is distributed by the Ductwork throughout the house. More information…
HVAC – Stands for Heating, Ventilation, and Air Conditioning.
Indoor Coil – See: Evaporator Coil
Outdoor Coil – See: Condenser Coil
Refrigerant – A chemical that cools air as it evaporates. Air conditioning systems use Refrigerant in the Evaporator Coil to cool air as it passes by.
R-22 – Hydro chloroflourocarbon (HCFC) is most commonly known ass R-22. R-22 has been the primary refrigerant used by cooling equipment manufacturers. HCFC’s are considered safe for the environment they contain chlorine that is considered to be an ozone-depleting chemical. The Clean Air Act has set a target date of January 1, 2010 for which HVAC manufacturers can no longer manufacture products that use R-22. Refrigerant manufacturers will still be allowed to produce R-22 until January 1, 2020.
R-410A – Hydro fluorocarbon (HFC) is an environmentally friendly refrigerant considered most likely to be the replacement for R-22.
Refrigerant Lines – Two copper lines that connect the Condenser (Outdoor) Coil to the Evaporator (Indoor) Coil.
SEER – Stands for Seasonal Energy Efficiency Ratio. An efficiency measurement that is similar to Miles Per Gallon for cars. The higher this number, the more energy efficient they system is. New units have SEER ratings from 10 to 17 BTUs per watt.
Single Package – One outdoor unit that contains both a heating and a cooling system.
Split System – A combination heat pump or air conditioner with indoor components such as a furnace or blower coil. To maximize effectiveness, Split Systems should be matched.
Thermostat – A device that allows you to control the temperature inside your home by telling the heating or cooling system how much air to produce.
Zoning – The dividing of a home into different areas each with their own heating and cooling properties. For example, you might prefer to have the kitchen area of your home be slightly cool, while at the same time keeping the temperature in the bedrooms warmer.